Devry ECET210 week 3 ilab

Laboratory Procedures
DeVry University
College of Engineering and Information Sciences

I.
OBJECTIVES

1. To analyze a
parallel AC circuit containing a resistor (R), an inductor
(L), and a capacitor (C).

2.
To simulate
the RLC circuit and observe the circuit responses.

3.
To build the RLC circuit and measure the circuit
responses.

II. PARTS LIST

Equipment:

IBM PC or Compatible

Function Generator

DMM (Digital Multimeter)

Parts:

1 – 470 ? Resistor 1 – 1 µF
Capacitor

1 – 47 mH Inductor

Software:

MultiSim
11

III. PROCEDURE

A. Theoretical Analysis

1.
Given
the R, L, & C parallel circuit in Figure
1, calculate the total equivalent admittance, Y_T, and the impedance,
Z_T, of the circuit at f = 550 Hz and 1 kHz. List the calculated
values in Table 1.

Figure 1: Parallel
R, C, L Circuit

Frequency Hz	L & C Admittances in Rectangular Form
Inductor GL – jBL	Capacitor GC + jBC
550
1000

Frequency Hz	Total Circuit Admittance YT
Rectangular Form GT + jBT	Magnitude	Angle
550
1000

Frequency Hz	Total Circuit Impedance ZT
Rectangular Form RT + jXT	Magnitude	Angle
550
1000

Table 1 – Calculated RLC Admittance
and Impedance Values

2.
Calculate
and record the following quantities:

Frequency Hz	IR (RMS). A	IC (RMS), A	IL (RMS). A
Magnitude	Angle	Magnitude	Angle	Magnitude	Angle
550
1000

Frequency Hz	{IR + IC + IL }= IS (RMS), A	IS = V * YT
Rectangular Form	Magnitude	Angle	Magnitude	Angle
550
1000

Table
2 – Calculated RLC Component Current Values

Does the sum of the magnitudes of the three currents I_R, I_C, and
I_L, in the table above, equal
the current, I_S, calculated directly in the last column?

(YES
or NO)

Explain why your
answer is what it is.

3.
Calculate
the power dissipated by the parallel resistor and the power supplied by the
source:

Frequency Hz	PR, W	PS, W
550
1000

Table 3 – Calculated RLC
Resistor Power Dissipation

B. Multisim Simulation and Circuit
Calculations

1. Launch MultiSim and build the circuit
schematic shown in Figure 2.Include
the AC Power source and the DMMs.

2. Set both DMMs, XMM1 thru’ XMM4, to read AC
measurements and Current, I. See fig. 2 below.

Figure 2: MultiSim RLC Parallel Circuit with Instrumentation

3. Activate the simulation and record the current
readings for both frequencies:

Frequency Hz	IS (RMS), A	IR (RMS), A	IC (RMS), A	IL (RMS), A
550
1000

Table 4 – Current
Measurements Simulation Results

4. Do the current values in Table 4 agree with
those obtained in Tables, 2, 3, & 4 of Part A? (Circle your answer)

YES NO

5. Remove the DMMs and attach the wattmeter as
shown below:

Figure 3 – AC Power Measurement

6. Record the measurement from the wattmeter.

Frequency Hz	Source Power, PS (Watts)	Power Factor
550
1000

Table 5 – Power Measurement
Readings

7. Do values
in the Tables 6 and 2 agree?
(Circle your answer)

YES NO

If there is any disagreement investigate the source of
error and report your findings below:

C. Construction of a Parallel R, L, C Circuit and
Measurement of Circuit Characteristics

1. Construct the circuit in Figure 1.

2. Set the function generator voltage to2.5V RMS and the frequency value to 550 Hz.

3. Turn the circuit on.

4. Record the
current reading.

I_S = _____________ (A)

5. Is this the same as the simulated and
calculated value? ________ (YES or NO)

6. Measure and
record the branch currents:

I_R = ________ (A)
I_C= ________(A) I_L
= ________(A)

Are the current readings
the same as your calculated and simulated values?

(Circle your answer)

YES NO

If you answered NO, explain why you think they
differ.

7.
Repeat Steps 2 through 6 with the frequency
generator set to output at 1000 Hz.

I_S = ______________(A)

I_R = ________ (A)
I_C= ________(A) I_L
= ________(A)

Are the current readings
the same as your calculated and simulated values?

(Circle
your answer)

YES NO

If you answered NO, explain why you think they
differ.

IV. TROUBLESHOOTING

Describe any problems encountered and how those problems were solved.

Laboratory Report Cover Sheet
DeVry University
College of Engineering and Information Sciences

Course Number:ECET210

Professor:

Laboratory Number:
4

Laboratory Title:Analysis
of AC Parallel RLC Circuit using Simulation and Construction

Submittal Date:Click here to enter a date.

Objectives:

Results:

Conclusions:

Team:
	Name		Program		Signature
	Name		Program		Signature
	Name		Program		Signature

Observations/Measurements:

III. A. 1. RLC Circuit
Calculated Impedance and Admittance Values:

Frequency Hz	Susceptance, Siemens
Inductive, BL	Capacitive, BC
550
1000

Frequency Hz	Total Circuit AC Admittance, YT
Complex Notation	Magnitude	Angle
550
1000

Frequency Hz	Total Circuit AC Impedance, ZT
Complex Notation	Magnitude	Angle
550
1000

III. A. 2. RLC Circuit Calculated Current Values:

Frequency Hz	IR (RMS). A	IC (RMS), A	IL (RMS). A
Magnitude	Angle	Magnitude	Angle	Magnitude	Angle
550
1000

Frequency Hz	{IR + IC + IL }= IS (RMS), A	IS = V * YT
Complex Form	Magnitude	Angle	Magnitude	Angle
550
1000

Match? Yes _____ No ______

Explanation:

III A. 3. RLC
Circuit Calculated Power Dissipation:

Frequency Hz	PR, W	PS, W
550
1000

III. B. 3. RLC
Circuit Simulation Results:

Frequency Hz	IS (RMS), A	IR (RMS), A	IC (RMS), A	IL (RMS), A
550
1000

III. B. 4.
Simulation Values Match Calculated Values:

Match? Yes
_____ No ______

III. B. 6. RLC
Circuit Simulated Power Measurement:

Frequency Hz	Source Power, PS (Watts)	Power Factor
550
1000

III. B. 7.
Simulation Values Match Calculated Values:

Match? Yes
_____ No ______

Explain any mismatch:

III. C. 4. RLC
Circuit Measured Current at 550 Hz:

I_S = _____________ (A)

III. C. 5.
Value Matches Calculated and Simulated Values:

Match? Yes
_____ No ______

III. C. 6. RL
Circuit Measured Currents:

I_R = ________(A) I_C
= ________(A) I_L= ________(A)

Match? Yes
_____ No ______

Explain any mismatch:

III. C. 7. RLC
Circuit Measured Current at 1000 Hz:

I_S = _____________ (A)

I_R = ________(A) I_C
= ________(A) I_L= ________(A)

Match? Yes _____
No ______

Explain any mismatch:

Questions:

1.
Construct a Phasor Diagram to represent the source current and the branch
currents, I_R, I_C, and I_L through the resistor,
capacitor, and the inductor. The diagram does not need to be drawn to scale.
However, the values of the items represented must be included in the diagram.

2.
Did
you notice any interesting feature in the lab exercise with regard to the two
different frequencies chosen for the experiment?

3. In the Multisim simulation, change the
frequency of the source to be between 725Hz to 735 Hz (in increments of 2 Hz)
and record the inductor and the capacitor currents.

Frequency, Hz	IR, mA	IC, mA	IL, mA
725
727
729
731
733
735

What do you notice from the readings?

Grade:

Deliverable	Points Available	Points Achieved
Laboratory Cover Sheet	8
Working Circuit(s)/Program(s)	8
Observations/Measurements	6
Questions	8
Total Points	30
Comments: